Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Parts & Accessories
$19.99 - $24.99
- Supplies full wheel illumination for 700c/29in wheels and smaller
- Approximately 40 hrs of battery life
- Water resistant design
- Includes 3 (AA) batteries
- Sold individually (1 wheel)
- Easy to install
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims.
21mm width fits:
- ZTR Olympic
- ZTR Iron Cross
- ZTR 355
- ZTR Alpine
- ZTR Crest
- ZTR Alpha 340 (2 layers)
- ZTR Alpha 400 (2 layers)
- Most road clincher rims
25mm width fits:
- ZTR 355 (26", 650b, 29")
- ZTR Crest
- Crest MK3
- ZTR Arch EX
- ZTR Flow EX
- Crest S1
27mm width fits:
- ZTR Flow EX
- ZTR Bravo
- ZTR Hugo 52mm
- Arch S1
- ZTR Rapid 28
- ZTR Rapid 30
- Arch MK3
30mm width fits:
- ZTR Flow MK3
$18.00
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair.
Identifying your Hugo rim and selecting the correct valve stem:
Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim.
Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads:
MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
$81.80 - $109.99
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.
- End Cap Included
$99.99
Upgrade or refresh your Bontrager wheels.
Genuine replacement parts
Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered.
- Replacement freehub body
- Compatible with Bontrager Rapid Drive 108 hubs
- Pawls and springs sold separately
- Install 3 pawls/springs for 54 tooth engagement or 6 pawls springs for 108 tooth
$105.00
Upgrade or refresh your Bontrager wheels.
Genuine replacement parts
Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered.
- Replacement freehub body
- Compatible with Bontrager Rapid Drive 108 hubs
- Pawls and springs sold separately
- Requires Micro Spline specific end cap
$119.99
Upgrade or refresh your Bontrager wheels.
Genuine replacement parts
When it's time to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered.
- Replacement freehub body
- Compatible with Bontrager hubs using the DT Ratchet EXP platform
- For use with SRAM XDR cassettes
- Includes 12mm thru-axle end cap
$9.99 - $15.99
These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance.
Key features:
- To be used exclusively with Bontrager Tubeless Ready (TLR) wheels
- Required for Bontrager's Tubeless Ready (TLR) system setup
- Removable valve core for easy sealant fill
- Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40
- Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels
$20.99
These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance.
Key features:
- To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels
- TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion
- Rim Strip replacement is recommended if removed from the wheel
- For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service
$24.99 - $25.00
Bontrager Tubeless (TLR) Rim Tape creates an air-tight seal that covers spoke holes in the rim for easy tubeless tire setup and installation. The tape securely bonds to the rim and doesn't leave residue when removed. For use with wheels approved for TLR Tape-based tubeless conversion.
- Provides durable, air-tight seal over spoke holes for tubeless conversion
- Wrap four wheels with a single layer of tape or two wheels with a double layer
- Provides secure adhesion to rim without leaving residue when removed
- Thoroughly clean and dry rim bed before applying
- For use with rims approved for TLR Tape-based tubeless conversion
$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).
$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation.
The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included.
- 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center
- Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels
- Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels
- Includes cassette spacer
- Material: Aluminum
$70.00
- Wheel bearing kit front/rear
- Bearing dimensions: 17 x 30 x 7mm
- Material: steel
- 2 pieces
$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm.
Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
$390.00
- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
$390.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
- Kits include Freehub body with CeramicSpeed
$206.00
Zipp Speed Weaponry Rear Axle Conversion Kit
- Not to be used on 188 V6 or earlier rear hubs
- Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed
$227.00
Zipp Speed Weaponry Rear Axle Conversion Kits
- Converts a road disc into a track disc rear
- Fits black 2013 188 V8 disc hubs only
- Fits Zipp 900 and Super-9 Discs
$21.00
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals.
Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
$108.00
Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1)
Compatible With:
HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
Page 1 of 14
Next page