Parts & Accessories

Replacement axles for MX-2000 hubs. Size: 14 x 100 x 165mm - Supplier Part: KT-M18F - MPN: 370666 - Front/Rear: Front - Diameter: 14mm - OLD: 100mm Size: 14 x 110 x 180mm - Supplier Part: KT-389R - MPN: 370668 - Front/Rear: Rear - Diameter: 14mm - OLD: 110mm Size: 3/8-inch x 100 x 165mm - Supplier Part: KT-M17F - MPN: 370667 - Front/Rear: Front - Diameter: 3/8-inch - OLD: 100mm Size: 3/8-inch x 110 x 180mm - Supplier Part: KT-M88R - MPN: 370682 - Front/Rear: Rear - Diameter: 14mm slotted for 3/8-inch - OLD: 110mm

Replacement axles for Black Ops MT-3100 hubs. Bearing shoulder to bearing shoulder is 59mm. Size: 3/8-inch x 100 x 140mm - Supplier Part: KT-M37F - MPN: 370685 - Front/Rear: Front - Diameter: 3/8-inch - OLD: 100mm Size: 3/8-inch x 110 x 175mm - Supplier Part: KT-M98R - MPN: 370686 - Front/Rear: Rear - Diameter: 3/8-inch - OLD: 110mm

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair

- Eady to install - Spoke mounted - 2 per set

- Variable widths - Left: 35mm - Center: 52mm - Right: 40.5mm - Length: 127.5mm - Overall: 148.5mm

Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench

Replacement clear plastic spoke guard.

• Locking skewer set • Cro-Mo • 70g (set)

• 5-sided key locking skewer set • Chromoly axles • 6061 anodized aluminum • Includes seat and F+R wheel skewers • 95g (set)

- Variable widths - Left: 32mm - Center: 52mm - Right: 32mm - Length: 116mm - Overall: 137mm

Replace the loop that goes around your left chainstay to secure your coaster brake arm with this Sunlite replacement part. It's made of full stainless steel, and it includes a nylock nut, washer, and bolt.

- Type: Skewer only - Length: 220mm

- Converts Schrader rims to Presta - Rubber - Sold individually

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

Wheel Freehub Kit SRAM XDR for Super 9RB - Compatible only with the Super 9 - Compatible With: WH-SP9-CCR-A1

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Grade 10 chromium steel balls

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

Origin-8's Torq Lite Track Cog Lock Ring 1.29" x 24 tpi with left-handed threaded thread is the only lock ring you need. Hardened threading and extra material make this highly durable to help you go the distance.

Origin-8's Pro Pulsion Rim Strips are made from a super-durable, environmentally friendly PVC material.

The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications

These freehub bodies fit only the older Spoon hubs, not compatible with the new Oozy or Spike hubs.

- Axle adapters for CX/GX/MT/FB-1110 Elite Series front hubs - Available in standard QR, 12mm, 15mm, and 20mm thru-axle options - Material: Aly - Color: Blk

Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.